SWIX VALLATIPS SWIX WAX TIPS FOR
ÖPPET SPÅR MÅNDAG THE VASALOPPET WEEK
GÄLLANDE Måndag 24.02.2014 | FOR Monday February 24th 2014 | |
Detta vallatips är baserat på väderleksprognoser och testing. TEMPERATURPROGNOSSälen kl. 07.00 +5ºC Evertsberg kl. 10.00 +5ºC Mora kl. 14.00 +6ºC STRUKTURStenslipade skidor: Medium. Kom ihåg att rill ovanpå stenslip ofta ger bättre glid. Swix Rilljärn:1,00 mm rätt (vals som präglar en rätt struktur) (T423/T406). GLID - Alternativ 1:1. Värm in LF8, låt kallna. Värm in en gång till, efter avkylning sickla av med plexisickel och borsta med Swix brons- eller stålborste. 2. Avsluta med Swix blå nylon poleringsborste. GLID - Alternativ 2 - racing:1. Värm in HF8 eller Vit Marathon låt kallna. Värm in en gång till, efter avkylning sickla av med plexisickel och borsta med Swix brons- eller stålborste. 2. Lägg på Cera F FC10X. Använda vallajärn på ca. 170°C. Dra järnet snabbt över belaget. Vänta därefter i ca. 5 minuter och borsta upp Cera F pulvret (inte bort) med en hästhårs- eller vildsvinsborste. Dra med järnet snabbt en gång till. Vänta i ca. 10 min. och borsta bort från belaget med en hästhårs- eller vildsvinsborste. 3. Avsluta med Swix blå nylon poleringsborste. FÄSTE:1. Rugga fästzonen med slippapper #100 (Swix T330 el. T0011). 2. Spraya på ett lager KB20 grundklister. 3. Lägg på ett tunt mellan lagerKX35 Violett Special klister. 4. Avsluta med ett lager KX65 rött klister Detta var dagens vallarekommendation för Öppetspår Enligt prognos regn mitt på dagen. LYCKA TILL! | These wax tips are based on weather prognoses and testing. TEMPERATURESSälen kl. 07.00 +5ºC Evertsberg kl. 10.00 +5ºC Mora kl. 14.00 +6ºC STRUCTUREStone ground skis: Medium to coarse structure. Remember to use hand structure on stone ground skis for better glide. Swix Structure Tools: Imprint Tool Roller (T423/T406) “Straight”: 1.00 mm (imprint roller that gives straight structure) GLIDE - Alternative 1:1. Iron in LF8. Let cool off. Iron in once more and let cool off. Scrape off with a Swix Plexi Scraper, and brush with a Swix Bronze or Steel Brush. 2. Finish with the Blue Nylon Polish Brush. GLIDE - Alternative 2:1. Iron in one layer of HF8 or DHF104 White Marathon. Let cool off. Iron in once more and let cool off. Scrape off with a Swix Plexi Scraper, and brush with a Swix Bronze or Steel Brush. 2. Apply Cera F FC10X with an iron temperature of approx. 170°C. Make one fast continuous pass with the iron with a constant pressure – take one side of the groove at the time. Let cool approx. 5 min. Brush up the powder (not away) with a horsehair- or wild boar brush. Iron the powder in one more time in the same way. Let cool approx. 10 min. Brush the excess powder thoroughly away with a horsehair- or wild boar brush. 3. Finish with the Blue Nylon Polish Brush. GRIP:1. Sand (rub) the grip zone area with #100 grit silicon sandpaper (Swix T330 or T0011). 2. Spray on a thin layer of KB20 Base klister. 3. Apply a thin mid layer of KX35 Violet Special klister. 4. Finnish with a layer of KX65 red klister. This is our recommendation for tomorrow’s conditions in the Vasaloppet track. Forecast: Rain in the middle of the day tomorrow. We wish everybody a nice trip! |